If we talk about plasma cutters, they’re the best excellent productivity-boosting tools. We know it can be daunting to pick up a plasma cutter as many things need to be considered. Of course, you don’t want a wrong purchase. Some plasma cutters are expensive but not up to mark, so we’ve got your back.
However, everyone needs a cost-effective tool that’s why VEVOR introduced its CUT50 Plasma Cutter comes in a complete package like well-constructed material, power source and duty cycle.
But apart from these factors, you should consider portability, safety gear, durability, versatility, and price. In this review guide, you’ll get a detailed discussion on the VEVOR CUT50 Plasma Cutter’s worth and compatibility with other products. However, this CUT50 plasma cutter is not a cutting torch; we’ll discuss further how it works.
VEVOR CUT50 Plasma Cutter Reviews
Let’s start work on the 20-gauge metal sheet. We’ll tell you step by step how to use the VEVOR CUT50 Plasma Cutter and whether it works or not. First, it’s important to note that using a plasma cutter differs from having a touching torch. Let’s see how it works. There’s no need to hold the tip off the metal surface; the tip should contact the metal while cutting with the plasma cutter.
You’ll achieve a perfect cut while placing a tip on the metal and dragging it along. A post-flow air lasts around three to four seconds which is ideal. Although the plasma cutter is plugged into a 110-volt outlet, the speaker is set to its maximum power of 51 amps, possibly contributing to a lower power output.
Wow, you can see in the image it successfully cuts through 20-gauge metal when the air pressure is set at about 80 pounds, and it also goes well with the thinner piece of around 3/32 inches. But remember that speed should be reduced slightly for a thinner metal cutting piece.
One more thing to remember is that when you see a spark flying up instead of going down, then you need to slow down the cutting speed; that’s a sign that you’re cutting too fast.
So now I’ll take a pair of scraping blades and break that off, which will be fine. But let’s see and make another cut, but this time, we need to slower down the speed. A cut got a little slag draws. Also, we get a slag on the backside, but undoubtedly, it’s a good cut. You can quickly clean that with a grinding machine and or flat wheel.
Now let’s go with the 10-gauge, an eight-inch piece. It’ll feel rusty, but I suggest you slow down with this one. Yooo… it looks so natural and slaggier and thicker.
The next step is to check out with three-sixteenth thick- use a straight edge. In the image, you can see that you’ll receive more swag with three-sixteenths.
Let’s see how the cut looks on a quarter-inch rusty crusty, but before it, there is a need for 110 plugged. It goes really slow on this piece.
Unfortunately, it won’t be a clean cut, as the plasma cutter machine has yellow and green lights. It’s crucial to notice the yellow light when you’re cutting, never forget that and never cut too much if the yellow light blinks.
Features
● Convenient Dual Voltage
● Universal USB Port
● Dustproof Switch
Pros
● Give perfect cuts on Aluminum, Copper, Stainless and Mild Steel
● Easy To Use
Cons
● Portable in Size
● Not Compatible with rusty crust
Note: When the machine is running, allow the fan to cool it down and allow cuts to be made. Avoid continuously cutting until the light indicator is on automatically and then shut offs. It’ll reduce the machine’s lifespan if you don’t do this. While running the machine, understand limitations and capabilities and use it wisely; a little consideration is needed.
Testing the VEVOR CUT50 Plasma Cutter
So now we need to do a few more steps and then will come to final consideration. The cutting process stopped after being connected to a 20-amp breaker, and a 110-volt power source caused the breaker to trip. All of this happened to an overload. But if you’re cutting a quarter-inch metal using a 110-volt setup, it’s perfectly good to go; however, dealing with sheet metal is a bit challenging, a material we frequently use for our rat and hot rod projects.
It would help if you took a 220V plug from the plasma cutter or bought it. You’ll do it correctly if you cut this plug off and install it. The green wire will go on the top side, and black and white will go into the left and right sides.
Now if you do a quarter ranch cutting, it comes out perfectly clean. Furthermore, with the 220V, it also cuts a lot better.
It’s time to cut the three-sixteenths and pass the stress test to see how much it cuts before it shuts off and overheats.
Well, it’ll cut, but unfortunately, if you do more cutting on thick metal, you’ll end up cutting the edge of the piece. One of the best things about it is that it will not overheat and that it will have a long lifespan. In terms of cutting sheet metal, it really works well. However, it cuts more rapidly to 220.
Is VEVOR CUT50 Plasma Cutter Worth It?
Off course, they’re such light in weight. Due to their quality and features, the price is unbeatable as we compared to other manufacturing companies. You can count on them for a complete package of content that doesn’t get hot easily. Do you know you’ll get 30 days of free returns if you discover any faults? So, we all know that no brand gives you this type of offer. All we say is that the VEVOR quality and high customer priority stand out in the market.
FAQs About VEVOR CUT50 Plasma Cutter
1-What is the required amount of air for a cut 50 plasma cutter?
In terms of tank capacity, it has around 100 to 120 litres, which is really not enough for long cuts.
2-Can a plasma cutter with a 50 amp motor cut thick metal?
With a cutting thickness of 3/4 in., the CUT-50 Plasma Cutter is ideal for portable repair work and small business projects.
3-What are the limitations of plasma cutters?
There are a few drawbacks associated with plasma cutting, however. Thicker or denser metals cannot be cut using most plasma cutters. Generally, plasma ranges about one inch due to its fleeting nature.
4- Before purchasing a plasma cutter, what should I know?
Ensure you have an adequate air supply for your plasma cutter, read reviews, determine the power and compatibility, and the, most important thing is to always purchase from a reputable vendor.
Bottom Line
This VEVOR CUT50 Plasma Cutter is a value for money for sure. It works really well with 220V. It’ll never trip out your machine or overheat the machine. You’ll never get such a handy plasma cutter anywhere. This product comes up with all the plug you only needs to buy a 220v plug.
If you buy this product right now, then you’ll get a discount of $10 as these products are in high demand in the market, so their prices are skyrocketed, but VEVOR is still giving a decent discount to their customers. So don’t wait and immediately buy your handy VEVOR Cut50 Plasma cutter.
