All

Customer Reviews

  • 4.7
  • 4.5
  • 4.6
  • 4.7
Alan N. Alan N.
Like many have already have posted, do research
My machine was dispatched from Germany and arrived ten days earlier than promised. I have not run the machine yet. I didn't expect to unpack, connect and start work. Up to now I have found a couple of faults: The control panel was hanging down It was only held on by two of the four studs. The power control knob stand proud and it would seem pressure on it in transit had caused the not very securely held studs to become detached. Easily fixed pop rivets. In order to properly remove the film from protective screen in the cabinet door I removed the frame which was fixed with the same studs as on the control panel. I was very care full but even so one studs became detached. I really was very careful using not more pressure than finger tight. Refixed stud with gap filling supper glue. Its probably more securely fixed than the original. On line it is recommended you remove the blue film from the cooling motor, I needed to undo the four fixing bolts to do this properly. I noticed the bolts were too long sticking out as far if not further than the cabinet rubber feet. Shortened them. As long as there are no more serious faults I am very happy with the machine and the rapid delivery. If I had paid _6'000 for a Lazer Engraver I would have been very disappointed if it had the above niggling faults, but I paid a fraction of that. Up to now I am very happy with my purchase OrangeA.
0
NIKITA Thomas NIKITA Thomas
Great value for money
Arrived well packaged, although this item need upgrades it's a great starter machine reasonably priced. Although not ready to use straight out of the box if you are willing to dedicate time to learning your way around the machine it is great.
0
Chris Chris
Fantastic machine at a good price.
Great machine. Delivery took about a week, and it worked straight out of the box. All the mirrors came aligned. Cuts great into acrylic and plywood.It's recommended to get an air assist when cutting plywood to keep flaring to a minimum so you'll get nicer cleaner cuts.
0
Sally Scott Sally Scott
Super Vevor 80W laser..well worth the price.
Recived this unit several months ago, so far it's been a brilliant piece of kit. I would recommend it as 5 star machine.
0
Vevor Customer Vevor Customer
Do your research before buying
If you have researched this and understand the problems with the bed, fan wiring and grounding, you are willing to spend a whole day setting it up and have the ability to make a parts to blow air and stop fires then go for it. Otherwise don't buy this, it's not for you.Power supply, it's marked as 110v on the site but the can be switched, mine was already set to 230v when it came. I would recommend removing the supply to check before you plug it in. Look for the little red switch and make sure it is right for your country.Power cable, the mains cable looks like a euro fitting so this needed changing. The fan and pump were euro too but these plug into the back of the machine so don't need changing.Mirrors, these were completely out of line, I ended up stripping the parts off the machine, cleaning up the edges, switching the screws for better quality M3 hardware, then realigned everything. You need patience for this step, all in it took about 4 hours.This laser needs a fan over the work, these are easily 3d printed, I chose a 3d printer blower fan, having the compressor going was a pain. Wired to a separate 12v supply with a power switch drilled into the control panel.The bed, this is terrible, remove the middle spring section and replace it with some sort of mesh. I used the mesh from an unused small disposable barbecue.My summary - this is great, really really great. But be aware you are buying a device that needs attention. I hooked up the power about 6 hours after opening the box. I removed all the blue film on the metal parts and checked every connection, some were loose, 1 wasn't connected.Look at the different software too, k40 whisperer is extremely good.
0
f f
Great help from the seller
This is a generic laser engraver, everything needed in the box, I can recommend seller sheepic
0
Vevor Customer Vevor Customer
40wt laser cutter engraver
I'm very pleased with my laser cutter. It does what I want it to do. The only downside was everything was in Chinese on the disc. So I researched you tube and learnt how to use it on there.
0
NIKITA Thomas NIKITA Thomas
Great value for money
Arrived well packaged, although this item need upgrades it's a great starter machine reasonably priced. Although not ready to use straight out of the box if you are willing to dedicate time to learning your way around the machine it is great.
0
Sally Scott Sally Scott
Super Vevor 80W laser..well worth the price.
Recived this unit several months ago, so far it's been a brilliant piece of kit. I would recommend it as 5 star machine.
0

People Who Bought This Item Also Bought

44-330-175-5511 Monday to Friday, 08:00-16:00, GMT+1 ©2009 - 2022 VEVOR All Rights Reserved