VEVOR Induction Heater Bolt Removal, 1800W 230V Magnetic Induction Heater Kit, Handheld Nut Buster Tool, Mini Heating Machine for Rusty Screw Removing, Car Garage Repairing Tools with 4 Coil and Box

Heat Induction Gun for Rusty Bolts with 1800W and 8-second Heat-up for Fast Disassembly

This heat induction gun for rusty bolts delivers 1800W of output power, bringing metal up to the desired temperature in as little as 8 seconds, faster than many lower-wattage induction tools used for similar repair work around the shop. The full heating cycle then runs for 25 to 40 seconds to ensure even heating throughout the fastener, rather than only on the surface, which helps loosen corrosion more completely before removal begins on the workpiece.

Because the unit relies on magnetic induction rather than an open flame, there is no need for water cooling or exposed heat sources during operation. It makes the tool safer to use in confined engine bays, around fuel lines, or in other tight garage spaces where rusty, stuck bolts and screws need to be removed quickly without damaging nearby parts, hoses, or wiring.

Separated Motor Module with Automatic Cooling Fan for Extended Component Lifespan

Separating the motor module physically from the main heating assembly helps to dissipate heat and protect sensitive internal components from the high heat generated during repeated heavy-duty cycles. This design works in conjunction with a built-in cooling fan and an overheating guard to control internal temperatures during taxing repair sessions in the shop, even under heavy, continuous load over long stretches of repair work.

The fan is automatic and comes on without the operator needing to monitor or turn it on manually during the job. The motor module and the automatic cooling system are separated and assembled into a single unit, giving this heat induction gun for rusty bolts a longer working life, even when used repeatedly throughout a busy day of automotive or mechanical repair work in a demanding garage environment.

Shoulder Strap Design with Secure Ergonomic Grip for Easier Extended Handling

The main unit comes with a shoulder strap that makes it easier to carry and position during extended use, which is useful given the tool's larger 9.8 lb build and higher-power output compared to lighter induction heaters used for smaller, lighter-duty repair tasks around the shop or garage. The strap helps distribute the unit's weight, allowing technicians to move between work areas without added strain on the arms or shoulders.

The handheld grip is built to stay secure during operation, helping reduce wrist fatigue over the course of a repair session that may involve several rusted or stuck fasteners in a row. The hand remains unobstructed while holding the unit, offering clearer visibility of the coil and the fastener being heated, along with greater security when working close to hot metal surfaces and parts.

4 Heating Coils with 0.2-1.6 Inch Diameter Range for Versatile Fastener Sizing

Four heating coils are included in the kit, covering nut heating diameters from 0.2 to 1.6 inches (5 to 40 mm) to accommodate a variety of fastener sizes encountered in automotive and mechanical repair work. The coils are wound with 0.16-inch (4 mm) copper wire built to handle the unit's higher 1800W power output without overheating during extended or repeated use throughout the day on the job.

This range of coil specifications enables the tool to handle complex and delicate metal-heating challenges, from smaller screws and bearings to larger gears and structural fasteners on heavier equipment and machinery. Having multiple coil sizes on hand means technicians don't need to switch tools when moving between different fastener sizes on the same repair job, saving valuable time on the worksite each day.

Lockable Toolbox with Theft-Resistant Storage for Secure, Organized Transport

The kit is stored and transported in a lockable toolbox measuring 16.5 x 12.4 x 5.4 inches, which keeps all four heating coils organized and protected from damage when not in use. The locking mechanism also helps guard against theft when the kit is left unattended in a vehicle, job site, or shared garage space overnight or between work shifts throughout the week and across multiple separate jobs and locations.

Having everything contained in a single case makes this heat induction gun for rusty bolts easier to transport between job sites or store on a shelf between uses. For technicians who move between repair locations throughout the week, a secure, organized case saves time that would otherwise be spent tracking down loose coils or missing accessories before starting the next scheduled job.

Heavy-Duty Heat Induction Gun for Rusty Bolts with Copper T2 Coils for High-Intensity Repair

Built from Copper T2, Aluminum 6063, ABS, and PA66, this heat induction gun for rusty bolts is constructed for larger, thicker workpieces that require short-term, high-intensity heating rather than extended continuous use throughout the day. With a maximum continuous operating time of 90 seconds, the design favors quick, concentrated bursts of power over long, sustained heating sessions on a single workpiece or fastener at hand each time it's used on the job site.

This makes it well suited to heating heavy-duty mechanical bolts, screws, bearings, gears, and even frozen lathe fasteners that resist removal by hand or standard hand tools. Automotive and mechanical maintenance teams working with larger or thicker metal components can rely on this tool for fast, high-output heating when standard induction heaters aren't powerful enough for the job.