VEVOR Shallow Well Jet Pump, 1300W, 230V 4800L/H Maximum Flow Rate, PP Garden Well Jet Pump with 8 m Suction Height, Thermal Protection, European Voltage Standards, for Garden Irrigation Lawn Watering

1300W Garden Jet Pump with 4800 L/H Flow Rate and 48m Max Head for Multi Story Delivery 

The VEVOR 1300W garden jet pump has a 1300W motor, delivering a maximum flow rate of 4800 L/H (1268 GPH) and a maximum head lift of 48m (157.48 ft). This provides sufficient pressure for garden irrigation, water transfer, and applications requiring high lift. The 48 m maximum head allows the pump to deliver water over long vertical distances, though the flow rate decreases as lifting height increases. 

At a maximum flow rate of 4800 L/H, the pump moves enough water each hour to water multiple garden areas, fill a swimming pool or garden pond in a reasonable time, or water the lawn across a large residential or smallholding plot without having to run for longer periods of time like lower-flow pumps do to move the same amount of water.

8m Suction Height for Reliable Shallow Well and Surface Water Intake 

With an 8-meter (26.2-foot) suction height, the pump can draw water from a small well, cistern, rainwater tank, or surface water source up to 8 meters below the pump installation point. This suction range works with most shallow residential wells in European garden and smallholding settings, where groundwater tables are usually within the first 5–7 meters without needing to install a submersible pump in the well.

Should you have a backyard pond, a rainwater tank, or a cistern that draws water from a stream, the 8-meter suction height lets you place the pump below ground level or in a pump house above the water source and still draw water without any priming problems. The self-priming jet pump draws water through the suction pipe without submerging the motor, making installation and maintenance easier than with submersible pumps. 

Built In Pre-Filter and Thermal Overheat Protection for Long Term Secure Operation 

At the pump's inlet, a built-in pre-filter prevents sand, debris, and other particles from entering the impeller and volute. Well water and surface water sources often contain fine sediment that, if not pre-filtered, would build up on impeller surfaces and inside the pump housing over time. This would reduce flow efficiency, accelerate impeller material wear, and eventually cause blockages that stop the pump from working. The pre-filter removes these bits right where they enter, so the pump can keep moving clean water for as long as it is working.

Thermal overheat protection monitors the motor temperature while it is running and automatically shuts it off if it gets too hot. This prevents the motor winding insulation from being damaged by long-term overloading, blocked suction, or dry-run conditions. Normal operation can resume once the motor cools to a safe level. 

G1.0 in Ports and 230V 50Hz Compliance for European Piping System Compatibility 

Both the pump's inlet and outlet are G1.0 in (G 1 inch BSP thread) sizes. This is the standard pipe connection size used in European homes and farms for water systems. This port size fits directly into standard European garden irrigation pipework, hose fittings, and distribution manifolds, so you do not need any reduction or conversion adapters at the pump connection points. This means that the pump can be added to garden water systems that already use standard fittings.

The motor can run on AC 230V 50Hz power, which is the standard voltage and frequency for homes in Europe. It can connect straight to a standard garden power socket or outdoor circuit without the need for a voltage converter or frequency adapter. It works best on the standard European grid supply rather than a voltage that might not match the motor's design specifications.

1300W Garden Jet Pump with 3 Step Installation for Beginner-Friendly Setup 

The 1300W garden jet pump is designed for straightforward installation—and you do not need any plumbing skills; the tools that come with the pump are enough. The kit comes with mounting screws, a check valve, and an ergonomic carry handle. These are all the parts you need to finish a functional installation. Install the system as follows: connect the supply and outlet pipes to the G1.0's inlet and outlet ports; prime the pump by filling the priming port with water to remove air from the suction line; then turn on the power and start the pump. 

The kit comes with a check valve that prevents backflow through the suction line when the pump stops. This keeps the suction pipe full of water so the pump can start up again and flow right away on the next cycle, without having to be primed again. This automatic suction retention means that the pump is ready to go the next time it is turned on after the initial priming. 

Suitable for Garden Irrigation, Pool Filling, Lawn Watering, and Emergency Water Supply 

The 1300W garden jet pump is suitable for garden irrigation, pool filling, lawn watering, and emergency water transfer thanks to its 4800 L/H flow rate, 48 m maximum head, and 8 m suction height. Garden drip irrigation and sprinkler systems work better when the pressure remains consistent throughout the system. This ensures that all emitters in the zone receive the same amount of water, regardless of how far or high they are from the pump.

When filling pools and backyard ponds, the 4800 L/H flow reduces the time it takes to fill compared to using a mains-pressure hose. For emergency water supply situations, power-outage tank filling, fire-risk water reserves, or water transfer between storage tanks, low-flow operation allows the pump to remain standby-ready, drawing minimal power while providing immediate full-flow delivery when needed.