VEVOR Retractable Air Hose Reel, 3/8IN x 50FT Hybrid Air Hose Max 300PSI, Air Compressor Hose Reel Auto-Rewind with 5FT Lead in, Ceiling/Wall Mount Heavy Duty Single Arm Reel & 180° Swivel Bracket

50 ft Hybrid Polymer Hose Handles 300 PSI Across All Weather Conditions

This wall mount retractable air hose reel comes with a 3/8-inch hybrid polymer hose that is 50 ft long and has a working pressure of up to 300 PSI without deteriorating or deforming. The hybrid material remains flexible in cold and doesn’t melt in heat, with a working temperature of -4°F to 113°F. That range makes it a suitable option for unheated garages, outdoor service areas, and any workplace where temperatures fluctuate seasonally.

Normal rubber hoses are quite rigid in cold temperatures, hard to pull, and prone to splitting at bends. This hose resolves that problem by remaining manageable regardless of ambient temperature. The outer layer also resists abrasion from dragging across concrete floors, contact with vehicle undercarriages, and normal wear and tear in the shop that erodes softer hose materials over time.

Wall Mount Retractable Air Hose Reel with 180° Swivel for Full Coverage Reach

The 180° swivel bracket allows the entire reel to turn to follow the direction of the task, rather than constraining you to operate within a set angle. Swing it toward a bench on the right side of the bay, pull it toward a vehicle on the left, or feed it straight out in front – the bracket goes effortlessly to wherever the work is without resistance or binding. That’s the flexibility that separates a well-placed wall mounted retractable air hose reel from a fixed version, which results in difficult pull angles half the time.

The steel reel body carries the swivel's rotational strain without flexing or squeaking under tension. Wall, ceiling, and floor-mounting options let you set the reel where it fits best in your workspace layout. A ceiling mount lifts the hose path completely off the floor. A wall mount places the reel at a height that allows the hose to feed cleanly into a work area.

Auto-Rewind Drum with 4 Non-Slip Rollers and Locking Stopper for Tangle-Free Operation

Hand-winding a 50-ft hose after every task is a waste of time and all but guaranteed to cause some degree of tangling or inconsistent coiling. The auto-rewind drum mechanically pulls the hose back onto the reel when you’re done, feeding it in evenly without bunching. During hose extension and retraction, four non-slip rollers guide the hose, reducing friction and avoiding the edge wear that builds up when a hose repeatedly scrapes against a bare drum lip over hundreds of cycles.

With the adjustable lock stop, you can set the hose to any working length and keep it there without retracting mid-task. Cut it to the length you need, lock it off, and the hose stays exactly where you put it until you unlock it. That mix of auto-rewind and manual lock provides you with control on the job and ease when the task’s done.

5 ft Lead-In Hose with 1/4 in BSP Connector for Fast Air Tool Hookup

The 5 ft (1.5 m) lead-in hose connects the reel to your air compressor, eliminating the need for a separate floor-level hose run. This leaves enough slack to sit in a fixed position while the compressor remains on the ground and nearby, keeping the connection clean and out of the way. The fixed section is also short, so there is no slack hose lying across the floor between the compressor and reel base.

The 1/4 inch BSP connector at the lead-in end will connect directly to typical workshop air tools and compressor outlets. BSP threads seal securely and reliably hold pressure over many connect-disconnect cycles without leaking at the joint. A connector that sits perfectly every time also eliminates the slow pressure loss associated with a fitting that becomes loose over time, for everyday workshop use where the compressor is regularly hooked up and detached.

Spring Guard and Rubber Sleeve Protection at Every High-Stress Point

Most air hoses fail first at the two points where the hose leaves the reel drum and where it meets the end fittings – both areas flex frequently and wear faster than the remainder of the hose. The spring guard surrounds the drum exit point and guides the hose in a regulated curve rather than a sharp fold under tension. It is the sharp turns at that exit point that cause internal hose cracking, which can eventually lead to pressure loss or a full blowout.

The rubber protective sleeve covers the connection ends. This is where the hose is bent over and over again each time a tool is attached, or when it is bent in another direction near a fitting. These two protective features work in tandem to prevent damage to the same areas where hoses begin to fail and extend the hose's life with no further maintenance by the user. A longer-lasting hose means fewer replacements and less downtime waiting for a new hose to arrive.

Wall Mount Retractable Air Hose Reel Suited for Garages, Shops, and Mobile Equipment

This wall mount retractable air hose reel is securely mounted and will not move, become loose, or vibrate in use. It weighs 10.6 kg (23.4 lbs) and measures 13.6 x 5.7 x 14.9 inches. The steel reel body is made to withstand the daily rigors of a bustling workshop - repetitive extension cycles, hose tension under load, and the occasional bump from moving equipment nearby. It doesn’t need to be babied to keep working reliably over the long haul.

This wall mount retractable air hose reel is a great addition for car repair businesses, residential garages, professional workshops, and mobile machines where a fixed air supply is essential. Once it is mounted and connected, the system operates without constant modification – the reel quietly does its job in the background while you focus on the task. The two most obvious benefits you see on the first day of use are a clean floor and a hose that is always ready to supply air.