Customer Reviews for VEVOR Dividing Head 6"/160MM Dividing Head for Milling Machine 6-1/2"/168MM Universal Dividing Head 5"/128MM Indexing Head Milling 1:40 Dividing Head Milling for Milling Grinding Drilling

It is a good product that can be adjusted. I couldn't remove the universal play, the play was between 1-2 degrees, because the screw defective and inside - it barely came out... photo: screw.jpg and inside.jpg With a tap and die M20 die 1.5 mm I solved the problem and it works very well. picture: tap.jpg I put a material so that the screw goes hard. The rest is very good. picture: good.jpg I buy again 3 product I buy again 3 product

Instructions were poor got some good tables on line for free brown and sharp seems to use the same gear ratio so just used there tables used it to put hex on round bar so far

Needs some adjustment before use, but works good. I have used it for several different small jobs and been happy with the result. Might be smart to take it apart and clean out the factory grease and oil and replace with better quality. Very good value for the money.

This is a very nice dividing head for the money. Pretty well finished and smooth operating, very little lash in the gearing.If you were thinking to use an ER32 chuck in the headstock taper note that the taper is #2 Morse not #7B&S as stated in the specifications. That is really good news given that the ER32 chuck adapter for #2 Morse is much cheaper than the #7 B&S. They are also available with 10mm drawbar threads so you can eliminate the chance of slipping in the taper.I checked the run-out specifications and found the following: Radial run-out of the spindle nose spec 0.0006" Actual <0.0002" Radial run-out of spindle taper nose spec 0.0008" Actual was about 0.001" Radial run-out of spindle taper hole 4" distant 0.0014" Actual was 0.0025" Radial run-out of test bar with 3-jaw chuck 0.0031" Actual was 0.003"So the specs were pretty close and my measurements might not be perfect. The run-out with the 3-jaw chuck was due the the chuck back-plate (spindle nose locating diameter had <0.0002 TIR). The locating diameter for the chuck had a run-out of 0.0025". That could be corrected by taking a few thousandths off the locating diameter, center the chuck and use the mounting screws to lock it in.

I looked at second hand dividing heads on ebay for a long time, but they were well worn. In the end I decided on a new unit and wasn't disappointed. Not so certain how long the rapid indexing location pin will last up, but it is easy to replace if it wears. It is a very solid head and suitable for any machine shop, let alone a home engineering workshop. Buy with confidence.

Very high quality product. As advertised! This dividing head is rigid as expected and can be used for professional work

Für den schmalen Geldbeutel und meine Zwecke echt hervorragend. Bedarf als ungeübter etwas mehr Übung

Wie gewohnt bei Chinaware sind messerscharfe Kanten keine Seltenheit. Das ist aber kein Hindernis, weil man ja sowieso alles auseinander baut, um dieses eklige Schmieröl zu entfernen. Die Genauigkeit des Morsekegels und des Backenfutters liegt beides bei 1/10 mm, so lala. Durch das Kegellager lässt sich die Drehachse spielfrei einstellen.

Was abit unsure at first as I had never heard of you but after doing some research on the Internet and reading the reviews, I placed my order. it came today and I have to say what a fast service you have given and the product is exactly what was pictured and described. It looks good and is solid, haven't tried it yet but can not see why it wouldn't perform like it says. Thanks