Customer Reviews for VEVOR Spray Paint Pressure Pot Tank, 30L/8gal Air Paint Pressure Pot with Manual Mixing Agitator, Leak Repair Sealant for Industry Home Decor Architecture Construction Automotive Painting, 70PSI Max

Bought it to spray PVA wood glue. Works fine!!! You need to experiment with pressure adjustments for tank and spray gun. Best value for money option.

Sprayed a staircases for a client, and what a difference this made. Was able to paint an entire runn without filling the paint.. game changer. Upgrading soon but this was a great way to see if a pressure pot was good for my projects.

Excellent service from Vevor - numerous email notifications of order progress and next day delivery. Very well packaged and courier was excellent too, equally with email notification of progress. The unit still has the internal paint tub fitted even though it's the resin model. I tried to remove the tube by unscrewing but it was well and truly in there - resulted in cutting it off. Even heating it didn't loosen the thread lock adhesive. The chamber is very well made, excellently painted and all the valves are high quality. I used a 6 litre mini compressor (6.3CFM) to pressurise it and it took about 40 seconds to reach 50psi, from no charge in the compressor. The chamber holds it pressure and does not leak at all over an hour of testing. I have not tried it for resin casting yet (too cold in the garage - only using the compressor to blow wood dust off the beer cans!) but I have absolutely no doubt it will be brilliant. I did consider converting a paint chamber - but no point. This unit comes complete and ready to go, why have the stress, extra time and effort messing about buying the extra valves, etc for a DIY unit. This ticks all the boxes and converted ready to go. Trust me - I did a lot of research before buying.

Brilliant set of dent pullers great value for money. A great set to complete my panel beating set of tools I bought 2 sets but the vevor set was cheaper than the other supplier. Very happy with this purchase.

I'm really happy with this pot. There are loads of videos on YouTube showing how to convert it for resin casting. I pressurise mine to 60 psi and it holds perfectly. Bear on mind you'll always lose a couple of psi as the air cools back down. To convert this in the same way I have, you'll need... 3/8x1/4 bsp male x male fitting 1/4 bsp Tee (all female) 1/4 female to male ball valve 1/4 male to whatever your compressor or pump uses 1/4 pressure gauge (the pot comes with one but I chose to get a sturdier one) Ptfe tape The pot also comes with a pressure release valve There are two holes in the lid, one is 1/4 and one us 3/8. I screwed the pressure release valve straight into the 1/4. I assembled the other as in the photo but switched the gauge and inlet around. use 3 wraps of ptfe on each thread. This is how I put it all together, do lots of research and make sure you're confident :) If this was useful or if you have any questions, pop to instagram and say hi! https://www.instagram.com/discover_rings/?hl=en-gb

It works perfect and it´s easy to adjust amount of coulor for different needs. Maybe the hoses could be a bit softer. Was also a bit hard to put all things together, but eventually I managed to make it work.

Not used it yet as I have not been doing anything to paint but we'll let you know later if it isn't good product

Excellent piece of kit. Sealed lid for first time, filled it with air to 50psi. Disconnected compressor and left for 3 days. The psi was still 50, never had that before with a pressure pot. Used it several times since and still holding pressure, no leakage at all. Good quality. I cut off the liquid out pipe inside as it interfered with caddy. Excellent thanks.

Fantastic Quality product, fast delivery and no damage to the box or product. Very impressive. Will order again

Έλαβα εχθές το δοχείο πίεσης χρωμάτων αλλά λείπουν από την συσκευασία οι 4 ρόδες. Παρακαλώ να μου τις στείλετε.Ευχαριστώ.