Customer Reviews for VEVOR Stainless Steel Prep Table, 24 x 18 x 36 Inch, 600lbs Load Capacity Heavy Duty Metal Worktable with Adjustable Undershelf & Feet, Commercial Workstation for Kitchen Restaurant Garage Backyard

Needed a rust proof work table with a small footprint for use in a greenhouse. Works perfectly. One minor complaint. The protective plastic protective tape on the table surface is not easy to remove.

Aufbau problemlos m?glich. Die H?he entspricht der H?he der K_henarbeitsplatte. Sehr praktisches Teil.

Simple easy to follow instructions

The only thing that I would change with the table is the "tape that is on the actual table. Hard to get off.

I ordered this to hold an aquarium that is 20 x 20. I figured it would weigh a little over 250lbs. I bought this table based on the specs that show it will hold up to 550lbs. It came with no instructions but it was quite easy enough to put it together without them.While the top does feel sturdy and substantial the legs are hollow. I like the look of the table so I may fill the legs with spray foam or something to make them a little sturdier. I doubt it would hold anymore weight if I do but it may hold off some dings.There are some pretty sharp edges on the legs but once they are connected together they're not accessible. An Allen wrench is included and the only issue I had was a bolt that was not drilled out with a hole. A pair of pliers helped.Overall it's a nice looking table. Kind of cheaply made, but it's also a cheap price. Not sure about the weight specs but for a prep table it's fine.

Nice size 24" x 24"; has a backsplash. Top shelf is reinforced by a substrate making it sturdy and rigid. Bottom shelf is not reinforced so flexible -- not meant to hold heavy weight -- it is a stabilizer for the legs. As with a lot of Chinese product; horrible instructions, but not hard to figure out on your own. With the little help the instructions does give you, and a basic understanding of what must go up and what must go down -- not too difficult to assemble. I laid the top upside down on the dog's thick dog pillow so as not to scratch it with the floor. Because of the backsplash it could not lay flat. Putting the dog bed under it gave it the cushion it needed to support the backsplash while I assembled it; and the dog was willing to contribute to the project. The only really difficult, and annoying, problem I had was removing the protective film. I noticed that it said on the box to remove the film within 30 days of packaging. I suspect that film was attached for a lot longer than 30 days between the journey to the USA and the time it sat in a warehouse waiting for someone to purchase it. I did not think I would ever get it off -- it took a real effort. But I did get the film off and the table cleaned up nice. It is being used as a support for a counter top oven while we remodel the kitchen. So easy to clean up spills. Once that project is done, I will relocate the table to the shop. It will be a great flat surface for working with polymer clay and other such crafts.

This table is great for use in the kitchen. It arrived with a few little dents and pings, not sure how b/c it was shipped in a seriously sturdy, taped box with edge guards. A couple of the legs were a little out of round but we still got it assembled. There was one screw that was the wrong size and when I contacted the manufacturer they sent out the correct one asap. The only problem I have had using the table is it still moves when I'm rolling out fondant even though the wheels are locked. I wish it had four locking wheels instead of just two. This is a great table to have and I'm pleased with it overall. It does take patience to remove the plastic coating used to keep it from being scratched, but I'm glad it was on there to prevent damage to the surface.

I have it outside by my pizza oven. After you open it you first have to Scrap the edges of each piece of film first with a razor or you won't be able to remove it. Not bad for the money. I dont like how if you pick up the table and something is on the bottom shelve the legs stay on the ground and the table separates from the legs. You then have to turn the table over and push the legs back In because they dont bolt or screw to the table they simply get pushed in. Really bad idea never had a table built like this before but overall it's a pretty good table for the price. I'd definitely recommend this table.

Perfect for my needs. Easy to put together. Looks good also

sicuramente non un prodotto al TOP della qualit acciaio AISI.... quello pi strutturato per laboratori.ma per la sua funzione di sorreggere una planetaria e qualche pentola risparmiando bei soldoni ne vale la pena! questo soprattutto se sei all'inizio attivit! o lo usi per diletto.riguardo la consegna nessuna riga n ammaccosemplicemente tavoli del genere "stile cinesat" (ne ho 3) a volte in alcuni punti iniziano ad ingiallirema se non ci si maneggia altro che strumentazione o alimenti secchi vanno benissimo