Souprava CNC 3018 routeru s laserovou rytkou 500mw laserovou rytkou Grbl vstřikování

It was a bit time consuming to put together the CNC, but the user manual was good. The CNC software works fine with the latest Windows 11 version. I have only tried one of the example files for cutting into oak. The default settings and the included bit did not give a very good result, but the machine worked fine and was very accurate.

Dobrý stroj. Trošku trvá sešroubování hliníkových profilů a seřízení souososti, ale dobře funguje a pro domácí použití je výborný. Uvítal bych kryt na plošný spoj s elektronikou. Jinak je opravdu potěšení se strojem pracovat.

Totally satisfied with the product and speed of delivery. The given accuracies are really respected.

A bit fiddly to assemble, product did not match product photos in listing but is still 100% functional. Know that you are not buying a production machine, it's for hobbyists and therefore limited in table size, spindle capacity and rigidity. There's lots of accessories to add on.

As decribed.Easy to assemble and working fine.

Perfect professionals. They solved my problem very quickly and replaced the faulty part. I recommend them wholeheartedly. I will continue to buy products from them.

The assembly instructions are rather like those you get with flat pack furniture, line drawings and a few lines of text, and are quite simple to follow. You even get the tools (hex keys) you need, though ball ends would have been useful on the M4 bolts. Some of the parts are supposed to be a specific distance apart however the cast aluminium corner joiners are a little too big to get one quite right. It was supposed to be 56mm but without filing down the joiners it ended up as 60mm, not of any consequence really. Some of these fittings did need a little filing to remove excess material, took minutes to clean them all up. There are no end switches so you have to ensure the job fits within the useable work space, there do seem to be solder pads (but no pins fitted) to the board where you'd expect so I'm not sure if they'd work even if I fitted a set though I might try it out. There are the pinouts fitted for an offline controller which should be any generic GRBL unit. Overall the assembly is very simple and quite obvious though if you get stuck or aren't sure just look up a build for a 3018 machine that looks the same and it will fill in any gaps you might have. I would think that most people could easily convert the box of parts onto a working machine in 2 hours. Once assembled the machine feels rigid and flex free, it is certainly more than rigid enough for the type of work it is likely to be used for and is robust enough not to fall apart !! The machine comes with a set of 30 degree v knife bits bits, these will be OK for general and letter engraving but you'll need a set of small mill bits to do much else. The laser is a 500mW low power unit with manual focussing which is good for surface burning, this can be upgraded if you want to do cutting. Overall a good and upgradeable machine.

ordered, payed and received, built together within 4 hours... working => nice and Thanks from Switzerland, a beautiful country, I write this text, only because I have to, min. 100 characters, this tie nearly out of writing and singing and drinking and writing again.

Man hat damit ziemlich viele Möglichkeiten, auch kleinere Spannvorrichtungen lassen sich damit bauen, man kann die Maschine auch mit eigenen Bauelementen vergrößern und erweitern, sogar eine Leistungsstärkere Spindel und bessere Antriebsmotoren lassen sich einbauen, ob man am Ende wirklich etwas mit dieser Maschine anfangen kann, liegt daher beim Werker und seinen technischen Fähigkeiten. Hatte mir dazu noch ein Set mini Spanzangen bestellt, nun kann ich auch mit nem 8ter Vhm Schaftfräser schön Material wegfräsen. Zustellungen bei Kunstoff und Holz sind bis 5mm auch überhaupt kein Problem, schön hohe Drehzahl, scharfes Werkzeug und schon läufts wie durch Butter.

Very good for the price and very accurate