VEVOR Electric Hoist, 399.2 kg Lifting Capacity, 850W 220V Electric Steel Wire Winch with Wireless Remote Control, 1219 cm Single Cable Lifting Height & Pure Copper Motor, for Garage Warehouse Factory

Electric Wire Rope Hoist with 100m Wireless Remote for Safe Hands-Free Operation 

This VEVOR electric wire rope hoist has a wireless remote that lets you control the hoist from up to 100 meters away, so you can raise and lower loads. The remote allows convenient operation while keeping a safe distance from suspended loads. 

Unlike wired controllers, the wireless remote provides greater flexibility when positioning yourself around the work area. With a cordless system, you can go where the job needs you to go, change positions as the load moves, and operate from different positions around the work area. There is a real safety benefit to being free in busy places like garages, warehouses, and plant floors, where being aware of your surroundings is important.

880 lbs Dual-Line Capacity for Engines, Transmissions, and Heavy Workshop Loads 

When you set this hoist to single-line mode, it can lift to 440 pounds. If you set it up with two lines, it can hold up to 880 pounds, which is enough for engines, gearboxes, compressors, heavy construction supplies, and most major lifting jobs in the workshop without pushing it too far. The 40-foot single-cable lifting height is tall enough to reach the ceilings of most garages and buildings.

The dual-line setup does more than just increase lifting capacity. Spreading the weight across two wire runs makes the lift more stable on the sides, which helps awkward or off-center loads rise more steadily. The two-line setup gives you much more control over lifting heavy things that might tilt or swing on a single hook point. This is something that single-line hoists of the same size simply can not do. The lifting speed of 33 feet per minute keeps work going along at a steady, manageable rate.

850W Pure Copper Motor with Active Cooling for Sustained Heavy-Duty Performance 

The 850W motor uses pure copper windings, which provide efficient power transmission and stable lifting performance during operation. In practice, this means the full-strength torque output remains the same throughout the work session, without performance dropping over time as it does with a cheaper motor that heats under load. When you have to lift big things over and over, that consistency is important every time.

When the motor is running, the built-in big cooling fan actively pulls heat away from the motor housing before it builds up to dangerous levels. Professional users who do many lift cycles in a day will notice the difference: the motor stays cool, performance remains stable, and service life is much longer than with passively cooled options. The 850W output rating reflects how much power this motor actually has, not just when it is drawing the most power.

Φ4mm 19-Strand Steel Cable for High-Tensile, Fatigue-Resistant Lifting 

This electric wire rope hoist's 4mm cable consists of 19 individual steel strands twisted together into a single, strong lifting line. This multi-strand design spreads the working tension evenly across the whole cable cross-section. This eliminates the stress concentration points that lead to fatigue fractures in single-wire cables over time at bend and spool sites. As a result, the cable maintains its maximum strength for much longer, even after being loaded and unloaded many times.

The cable's 19-strand design also keeps it flexible enough to spool on and off the drum without getting kinked or setting in a way that makes stacking less consistent. Its 4mm width and 12 meters length make it the right size for this hoist's 880-pound working capacity. It gives the tensile strength and flexibility needed for tough professional lifting jobs without adding extra weight or bulk.

Electromagnetic Brake and Emergency Stop for Instant Load Control and Safety 

This unit has two separate safety systems that work together to keep each lift under control from start to finish. When the motor stops, the electromagnetic brake instantly engages, locking the load in place without requiring continuous power to maintain the hold. There is no creep or slow descent—the load stays where you leave it until you move it again, which is crucial when working alone with heavy loads in the air.

This extra safety feature, the emergency stop switch, operates independently. If something unexpected happens in the middle of the cycle, like a load moving, someone walking into the work area, or an obstacle appearing, one press stops everything right away. The unit is suitable for professional and controlled settings because it has two backups. It is not just good for occasional home workshop use, where safety rules are easier to follow.

Electric Wire Rope Hoist Built for Garages, Warehouses, and Factories 

Installation is simple on purpose. You can use the included 2-channel mounting brackets to connect solid wooden or metal strips directly to ceiling crossbeams. The included mounting brackets support installation on suitable overhead structures, in accordance with the product instructions. This electric wire rope hoist can be mounted on the roof and is then ready for all the lifting jobs it was made for, from pulling engines in garages to moving stock in warehouses to handling parts on factory floors and everything in between.

The range of uses goes far beyond industrial areas. Use cases include ships, cars, lawn mowers, golf carts, rock placement, and putting up home decor. With a wireless range of 100 meters and a weight capacity of 880 pounds, most of these are actually possible. This VEVOR unit offers the capacity, control, and safety features professionals and skilled home users often need in a machine that works every time.