Clearance

VEVOR Electric Chain Hoist, 2200 lbs Load Capacity, 13 ft Lifting Height, 11 ft/min Speed, 230V, Single Phase Overhead Crane with G80 Chain, 10.8 ft Wired Remote Control for Garage, Shop, Hotel, Home

Single Phase Electric Hoist Rated for 2200 lbs Load Capacity

With a load capacity of 2200 lbs / 1T, this single phase electric hoist is powerful enough to handle heavier lifting tasks in a garage, workshop, or small commercial setting, without the need for a three-phase power setup. This hoist operates on standard single-phase 230V power, so it’s suitable for use in locations where three-phase electrical service is not readily available, including most home garages and many smaller shops.

The hoist itself weighs 97.4 lbs/44.2 kg, measures 15 x 6.9 x 11.8 in/382 x 176 x 300 mm, and is rated to lift substantial loads while remaining compact enough to mount in spaces with limited overhead clearance. That combo of size and a practical 2,200-lb capacity makes this hoist a good tool for engine work, equipment installation, or general heavy lifting where a permanent overhead crane isn't needed.

1.1KW Copper Motor with Aluminum Housing for Durable Operation

A single-phase 1.1 kW copper motor drives the hoist and has an aluminum housing that resists rust and corrosion from repeated use. This combination is important for hoists that will be used frequently in garages or shops, where moisture and temperature fluctuations can degrade less durable materials over time.

The housing features specialized cooling fins that facilitate rapid heat dissipation during operation, enabling efficient performance even during repeated lifting cycles within a single session. A motor that overheats quickly would slow down or even shut down during a task. The cooling design directly supports reliable, consistent operation. For users who run this single phase electric hoist through multiple lifts in a work session, the combination of motor power and heat management maintains steady performance without degradation over time.

G80 Manganese Steel Chain Lifts to 13 ft at 11 ft/min

This hoist features a G80 manganese steel chain with welded joints, rated for the heavy-duty load-bearing strength required to support a 2200 lbs capacity safely. The chain has a 0.25 in / 6.3 mm wire diameter and is rated to handle the stress of repeated lifting without stretching or weakening over time.

Lifting height is up to 13 ft / 4 m at a speed of 11 ft/min, enough vertical range for most garage or shop ceiling heights while keeping lift speed reasonable rather than dangerously fast. The lifting assembly is completed by a manganese hot forged steel hook with 360-degree rotation and a built-in safety latch, which allows the load to be positioned at different angles without disconnecting and reconnecting the hook. It gives you real flexibility in how you can maneuver loads when you have awkward angles or need precise positioning.

Limit Switch and Magnetic Braking for Safe Operation

A limit switch automatically stops the motor when the hook reaches the top or bottom of its travel, so there is no chance of overextending the chain or of slamming the hook into the housing at either end of its travel. This automatic cutoff is especially important in repetitive lifting tasks, where manually tracking the chain position on each cycle would be easily overlooked under time pressure.

If power is cut -- intentional shutoff or unexpected outage -- a side magnetic braking device kicks in immediately, holds the load in place, and prevents it from dropping. That instant stop is a critical safety feature for any load-bearing hoist, because a free-fall with a 2200 lbs load is a real hazard. This single phase electric hoist has two independent levels of protection during operation: the limit switch and the magnetic brake.

10.8 ft Wired Remote with UP/DOWN and Emergency Controls

Simple operation via a 10.8 ft / 3.3 m wired remote control with UP, DOWN, and EMERGENCY buttons makes it easy to use without extensive training. That length of cable provides the operator with the distance from the hoist itself to maintain a safe vantage point while still precisely directing the lift.

Rather than needing a separate cutoff switch, the remote offers a dedicated emergency button that provides a quick, direct way to stop the lift immediately if anything goes wrong during a lift. If you’re new to using a chain hoist, this simple three-button layout avoids unnecessary complexity, but still covers the basic functions you need to lift, lower, and stop safely.

Single Phase Electric Hoist Built for Garage, Shop, and Home Use

This single phase electric hoist is ideal for a range of environments, such as garages, workshops, small hotels, and home use, where you need to do heavier lifting tasks but not constantly. Its use of standard single-phase power allows it to be easily integrated into areas that would not normally support industrial-grade three-phase equipment.

The strength and construction quality of the hoist also make it suitable for factory, logistics, and agricultural applications where moderate lifting tasks are performed repeatedly. This single-phase electric hoist offers users who need dependable lifting power but don’t want to commit to a full commercial crane system a practical middle ground between manual lifting tools and large-scale industrial equipment.