Two Piece Toilets
Results for Two Piece Toilets
A macerating toilet system is a toilet paired with a built-in grinding and pumping unit that moves waste to a drain instead of relying on gravity. When the toilet is flushed, rotating blades cut solid waste and paper into a fine slurry, and a pump pushes that slurry through narrow pipework to reach the main drain line. Because the discharge pipe is small and the pump does the lifting, the toilet can sit lower than, further from, or below the level of the drain it connects to. The grind-and-pump cycle runs automatically after each flush.
Macerating toilet systems from VEVOR span about 500W to 800W of pump power, which sets how far each unit moves waste: vertical lift runs roughly 16 to 36 ft (5 to 11 m) and horizontal distance about 230 to 394 ft (70 to 120 m). Single-unit models serve a toilet on their own, multi-fixture models add inlets for a basin, shower or bath, and compact models fit tight rooms. Typical uses are basement bathrooms, garage and attic conversions, cloakrooms, and additions set well away from the soil stack.
5 things decide what you need:
- Lift and distance: measure the vertical rise from the toilet up to the drain stack and the horizontal run across to it, then pick a pump rated to clear both with room to spare.
- Fixtures to connect: decide whether only a toilet feeds the unit, or also a basin, shower or bath, since that sets how many inlets you need.
- Space and bowl depth: check the clearance from the wall to the front of the bowl so a rear macerator or slim unit fits the room.
- Power point: plan a fused connection outside the bathroom zone to run the pump motor safely.
- Discharge fall: allow a slight downward slope on horizontal pipe sections so the line drains between pump cycles.
Browse the full range of macerating toilet systems to compare pump power and inlet options, or step up to the wider toilets category for related fixtures and parts.
Macerating Toilet System Types at a Glance
The table below sets the four system types side by side on what separates them in practice, before the sections that follow describe each one in detail.
| Sub-types | Fixtures Served | Unit Footprint | Pumping Emphasis | Selection Note |
|---|---|---|---|---|
| Single-unit system | Toilet only | Compact all-in-one bowl and pump | Short runs to a nearby stack | Simplest choice where only a toilet is needed |
| Multi-fixture system | Toilet plus basin, shower and bath | Larger pump with several inlets | Combined load from fixtures used together | Pick when one pump must serve a whole bathroom |
| Basement upflush system | Toilet, plus optional fixtures | Standard rear unit behind the bowl | High vertical lift to an above-grade stack | Built for pushing waste up out of a cellar |
| Compact system | Toilet only | Slim bowl, low-profile rear macerator | Short routing within the rated range | Fits cloakrooms and under-stair spaces a standard toilet cannot |
VEVOR Macerating Toilet Systems for Basement Bathrooms, Remote Additions, and Below-Grade Installations
Are you looking for a macerating toilet system that enables a full bathroom installation in a basement, converted garage, or other area without gravity drainage? Macerating toilet systems grind up waste and pump it up through small lines to the existing drain stack. It solves the drainage problem in below-grade and hard-to-plumb areas. VEVOR offers a reliable range of macerating toilet systems for homes and businesses in areas where standard toilet plumbing cannot reach without major building work.
Explore Macerating Toilet Systems by System Type and Application Area
To choose the right macerating toilet system, consider the available space, the number of fixtures to connect, and the required pumping distance to the main drain stack. VEVOR organizes its macerating toilet systems by type and application, making it easy for homeowners and contractors to find the best upflush option for any installation.
Single-Unit Macerating Toilet Systems
Single-unit macerating toilet systems can be complete bathroom solutions that include the toilet bowl, the macerator unit, and the pump mechanism all in one small unit. These systems are easy to install in small bathrooms, wet rooms in the basement, and additions with only one outlet. Traditional gravity toilets require large-diameter drain pipes, whereas VEVOR single-unit macerating systems integrate the macerator and pump behind or beneath the bowl, discharging through a smaller 22 mm or 32 mm pipe.
Single-unit macerating toilet systems have a compact footprint, making them ideal for basement bathrooms with limited plumbing space and low ceiling height. It is easy for skilled do-it-yourselfers or plumbers to install VEVOR single-unit macerating toilet systems because they do not require breaking up concrete floors or rerouting major drain lines. There are different types of single-unit macerating toilet systems, and the outflow pipe can go up to about 100 meters horizontally or about 4 meters vertically to connect with the home drain stack.
Multi-Fixture Macerating Toilet Systems
Unlike regular toilet macerating systems, multi-fixture toilet systems can connect a toilet, basin, shower, and bath to a single macerating pump unit. This feature allows installing and using a full bathroom below grade without relying on traditional gravity drainage systems. VEVOR multi-fixture macerating toilet systems feature a larger pump motor and wider inlet connections, allowing them to handle waste from multiple bathroom fixtures simultaneously. This design prevents overloading and maintains consistent pumping efficiency.
Multi-fixture macerating toilet systems are often a good choice for homeowners who want to turn their basement into a bathroom and connect a toilet, hand basin, shower, or bath to a single compact discharge unit, rather than installing separate pumps for each fixture. Included in VEVOR multi-fixture macerating toilet systems are inlet ports large enough for standard basin and shower waste pipe connections, in addition to the main toilet inlet. The design makes it easy to plan the installation of multiple fixtures in a single macerating toilet system. VEVOR's multi-fixture macerating toilet systems are rated to handle the combined waste from all connected fixtures when used simultaneously, without straining the motor or causing blockages.
Macerating Toilet Systems for Basement Installations
For basement use, macerating toilet systems are set up as upflush toilets that address the main problem of installing a bathroom below grade: moving waste against gravity to a drain stack above the basement floor. For basement installations, VEVOR systems feature powerful pumps capable of moving waste over the vertical and horizontal distances typical in residential layouts. In every basement macerating toilet system, the macerating blade assembly turns solid waste and toilet paper into a fine slurry before pumping. This allows the discharge to flow smoothly through pipes with small diameters and helps reduce the risk of clogging.
VEVOR's up-and-over toilets for basement installations are designed to be quiet, so the macerating and pumping cycle does not disturb people living above the cellar ceiling. During the discharge cycle, noise levels are about the same as those of a typical home appliance, thanks to motor housings that block sound and pump mounts that isolate vibration. VEVOR macerating toilet systems for basement use are also designed to handle the varying water pressure and pipe routing issues that arise in below-grade installations. They support extended horizontal discharge runs that carry waste from basement bathrooms to the nearest above-grade drain connection.
Compact Macerating Toilet Systems for Small Spaces
Compact macerating toilet systems are designed to fit in small spaces like cloakrooms, under-stair bathrooms, garage conversions, and anywhere else where a full bathroom size is not possible, but a toilet installation is needed. VEVOR compact macerating toilet systems feature a slim toilet bowl profile and a low-profile rear macerator unit, keeping the installation from protruding too far from the wall. That means that the toilet can fit in places where a regular toilet and cistern combination would be too deep to install comfortably.
Due to their flexibility of installation, compact macerating toilet systems allow adding a toilet to almost any room in a house, as long as the discharge pipe routing stays within the system's rated pumping range. VEVOR compact macerating toilet systems include all the installation guides, connection fittings, and discharge pipe plugs you need to finish the job without buying additional parts. VEVOR makes small macerating toilet systems with white ceramic finishes that fit other bathroom fixtures and maintain a clean, integrated look in any small bathroom or cloakroom.
Matching a Macerating System to the Install Setting
Beyond the system type, where the unit goes drives the decision. This table pairs common install settings with what mainly governs the choice, the discharge route to plan for, and what to confirm before buying.
| Install Setting | What Mainly Drives the Choice | Discharge Route to Plan | What to Check Before Buying |
|---|---|---|---|
| Basement below the drain stack | Vertical lift height | Waste must climb to an above-grade stack | Confirm the rated lift clears the floor-to-stack height with margin to spare |
| Garage or attic far from the stack | Horizontal run length | A long, near-flat pipe run with a slight fall | A long run eats into lift, so a stronger pump leaves headroom on both counts |
| Cloakroom or under-stair toilet | Footprint and bowl depth | A short route to the nearest soil pipe | Measure wall-to-front clearance first so a slim rear unit does not crowd the room |
| Full bath with basin, shower and bath | Number of fixtures connected | Several inlets feeding one pump | Raise the shower tray so its greywater drains down into the inlet rather than pooling |
| Room with no nearby socket | Power point location | A fused connection beyond the wet zone | Plan a fused spur outside the bathroom zone rather than an in-room plug, per wiring rules |
Macerating Toilet Systems Installation and Features Guide
Knowing how to install a macerating toilet system and its main features helps people choose the right system for their needs and accurately plan the installation process before they buy. Installation of VEVOR macerating toilet systems is easy and reliable, allowing you to add bathrooms below grade or in remote areas without extensive structural work.
Installation Requirements for Macerating Toilet Systems
To work, macerating toilets need a cold-water supply line to connect to the toilet cistern, a power line to power the pump motor, and a discharge pipe to connect to the current drain stack or an outside drain point. VEVOR macerating toilet systems connect to regular cold water pipes in homes using push-fit or compression fittings that typically do not need any special plumbing tools. The macerating toilet system's discharge pipe should have a steady fall of at least 1% along its horizontal sections. It will help gravity drain between pump cycles and keep waste from building up in the pipe between flushes.
Usually, a fused spur link outside the bathroom zone is required for macerating toilet systems instead of a regular plug socket inside the bathroom. It is because of local bathroom electrical safety rules. VEVOR macerating toilet systems feature a motor protection system that instantly cuts power if the pump becomes too full or clogged. This helps protect the motor from burning out. Backflow prevention valves built into the discharge port of VEVOR macerating toilet systems prevent waste from flowing back into the macerator unit when pressure in the drain below changes while the system is running.
Key Features of VEVOR Macerating Toilet Systems
VEVOR macerating toilet systems feature long-lasting stainless steel macerating blades that keep cutting for years of daily use without needing to be sharpened or replaced in a typical home. The VEVOR macerating toilet systems protect the pump motors against overheating. They are rated for the duty cycle requirements of a home bathroom, where multiple flush cycles may occur during morning and evening peak times. The VEVOR line of macerating toilet systems is designed to be as quiet as possible. The motor and blade assemblies are designed to make the 10 to 20 second pump cycle that follows each flush as quiet as possible.
VEVOR toilet macerator systems feature a non-return valve at the discharge outlet that prevents odors from flowing back through the discharge pipe and into the macerator housing when the system is not in use. The sealed macerator case on each system helps keep waste smells out of the bathroom, whether the system is running or not. This feature keeps the bathroom as clean as a normal toilet installation. The removable housing panels on VEVOR macerating toilet systems make servicing easy. These panels let you check out and clean the macerator chamber without disconnecting the whole unit from its plumbing lines.
Best-Seller Comparison
The three systems in this range share the same ceramic upflush toilet and differ mainly in pump power and reach. The comparison below lines them up on the specs that actually separate them.
| Product | Pump Power | Max Vertical Lift | Max Horizontal Run | Extra Inlets | Antibacterial Pump Box | Best For |
|---|---|---|---|---|---|---|
| Upflush Toilet System, 800W, 4-Inlet | 800 W | 36 ft / 11 m | 394 ft / 120 m | 4 (WC + 4) | / | Longest reach and most inlets here; multi-fixture baths farthest from the stack |
| Upflush Toilet System, 700W, 3-Inlet | 700 W | 32.8 ft / 10 m | 328 ft / 100 m | 3 (WC + 3) | PP-GF20 casing, silver-ion | Balanced middle option; close to the top unit's reach at a lower power draw |
| Upflush Toilet System, 500W, 3-Inlet | 500 W | 16.4 ft / 5 m | 230 ft / 70 m | 3 (WC + 3) | PP-GF20 casing, silver-ion | Lowest power draw and shortest lift here; a single compact bath near the stack |
Why Choose VEVOR Macerating Toilet Systems?
When installing a toilet in a place where regular gravity plumbing is not possible or available, VEVOR macerating toilet systems can be a sensible, reliable, and affordable option. There are single-unit macerating toilet systems, multi-fixture toilet macerator systems, upflush toilets for basement installations, and compact macerating toilet systems for small areas. At VEVOR, you can browse all their macerating toilet systems and find the right upflush option for any below-grade or remote installation.
FAQs
How far can macerating toilet systems pump waste vertically?
Depending on the model and pipe routing, most VEVOR macerating systems can pump waste up to 4 meters vertically and 100 meters horizontally. If the discharge runs are longer, the pump motor may need to draw more power.
Can macerating toilet systems handle sanitary products and wet wipes?
No, macerating toilets should only handle poop and toilet paper. Items made of cotton, sanitary products, or wet wipes can get stuck in the macerating blades and damage or stop the pump motor. If you only use toilet paper rated for macerating systems, your system will work well for a long time.
Do macerating toilet systems require professional installation?
Professional plumbers and skilled do-it-yourselfers can both install VEVOR macerating toilet devices. Connecting the pipes does not involve breaking concrete or rerouting big drain lines; it just uses standard pipe fittings.
How loud are macerating toilet systems during operation?
During the 10 to 20 second pump cycle after flushing, VEVOR macerating toilet systems produce about the same noise as a typical home appliance. Motor housings that block out noise and vibration-isolated mounts cut down on working noise by a large amount.
How often do macerating toilet systems need servicing?
VEVOR macerating toilet systems need to be descaled with a specialist macerator descaler every three to six months for normal home use. This is to prevent limescale from building up on the internal components.
Are macerating toilets suitable for small bathrooms or basements?
Yes. These systems are built for exactly those spaces, grinding and pumping waste through small pipes so a toilet fits where gravity drainage cannot reach. For a tight room close to the stack, a lower-power choice like the 500W upflush system keeps the footprint and pipe run modest.
Where can I buy reliable macerating toilets online?
You can buy them directly from VEVOR's macerating toilet range, which lists each system with its pump power, inlet count, and pumping range. Ordering from the source means verified specifications, warranty coverage, and after-sales support rather than third-party guesswork.
Are macerating toilets suitable for all types of RVs?
Not universally. They run on household 110V power with a rear discharge, so they suit larger RVs that can draw stable shore, generator, or inverter power and have space for the pump. Rigs on a 12V-only supply are a poor match. Compare models in VEVOR's toilet range.
Can I install a macerating toilet myself or do I need professional help?
Many skilled DIYers install one themselves, since the rear-discharge design connects with standard push-fit fittings and needs no concrete breaking. Call a professional for the electrical spur and the tie-in to the main stack. A rear-discharge 800W system ships with the inlet and outlet fittings needed.