Jack Posts
Results for Jack Posts
A jack post is an adjustable steel support column that holds up a beam, joist, or floor from below. A telescoping or threaded section sets its height, and a flat plate on each end spreads the load onto the structure above and the surface beneath. Its function is to carry weight vertically, either to level a sagging floor or to hold a structure steady as temporary support during repair or remodeling work.
At VEVOR, our jack posts start with compact units of 11.6 to 16 inches and 2500 lbs per unit, and move up to short 19 to 36 inch posts rated at 18000 lbs. Tall telescoping posts reach 53 to 150 inches, and a screw jack post for 4 x 4 wood supports offers up to 24700 lbs. Compact posts suit low crawl spaces, short posts suit low basements that need high capacity, and tall posts suit full-height basement ceilings. Typical uses are basement support, floor leveling, crawl space repair, and remodeling.
4 things decide what you need:
- Load capacity: choose a rating above the weight the post will carry, using the per-unit figure.
- Height range: the post must reach from the floor to the beam within its adjustment range, without over-extending.
- Adjustment and locking: levers, twist nuts, and lock pins differ in how they set and hold height.
- Pack size: multiple posts spread the load across a long beam, so check how many are included.
Browse the full Jack Posts range or explore our wider Building Hardware category to find the right support for your project.
Jack Post Types at a Glance
The jack posts are grouped by height and how they adjust, and here is how the main types compare on height, capacity, and trade-offs.
| Type | Height Range | Max Load | Adjustment Method | Trade-offs |
| Compact twist-nut jack post | 11.6 to 16 in | 2500 lbs per unit | Twist nut turned with a wrench | Fits low clearances, but has the lowest rating here |
| Compact lever house floor jack | 12 to 16 in | 9700 lbs | Built-in lever, no extra tools | Higher rating at low height, but the single model has no locking pins |
| Short lever house floor jack | 19 to 36 in | 18000 lbs per unit | Built-in lever with lock pins | High capacity at low height, with limited reach |
| Tall telescoping house floor jack | 53 to 150 in | 11200 to 18000 lbs | Built-in lever with lock pins | Reaches tall ceilings, though the tallest range carries a lower rating |
| Screw jack post for 4 x 4 wood | 13.2 to 18.7 in | 24700 lbs, depending on the wood | Removable lever | Highest rating listed, but sized for 4 x 4 wood posts |
Steel Jack Posts Delivering Stable Beam Contact and Long Term Floor Leveling
Are your floors uneven, or are you planning a renovation that requires temporary beam support? Jack Posts are used to provide strong vertical support in basements, crawl spaces, and areas requiring structural repairs. These supports help spread the weight, keep the overhead beams stable, and prevent the structure from sagging further. Jack Posts are popular for leveling, remodeling, and reinforcing load-bearing areas in homes because they can be adjusted to different heights and are made of heavy-duty steel. Jack Posts are a useful and effective way to support buildings that have shifted due to age or are preparing for new construction.
Selecting the Optimal Jack Post: Key Technical Specifications
Load Capacity for Reliable Structural Leveling and Long-Term Stability
When comparing Jack Posts, it's important to choose the right load rating, as each structure has different weight requirements based on its age, design, and condition of the materials. Heavier beams, especially in older homes, need supports with a higher rating that can hold thousands of pounds without bending or losing stability. A reliable adjustable jack post lets contractors lift floors in small increments, preventing joists from bending and walls from cracking. Load capacity is one of the most important technical factors to consider for any reinforcement project because of the slow, controlled way in which pressure is applied.
When homeowners are fixing or stabilizing their foundations, they often use a basement jack post to give strong vertical support to their old basements or sagging floors. When floors sag due to water damage or natural settling, a properly sized support ensures the beam is lifted evenly, preventing stress from building up in one spot. Homes that are taller and have wider beam spans may need more than one post installed in parallel to spread the weight. In these cases, professional installers often look at models that can hold 18,000 to 20,000 pounds to ensure they will last a long time.
When contractors use House Floor Jacks to fix structural problems, they often use temporary shoring to lift and stabilize heavy beams safely. For repairs in a crawl space, lighter loads may be enough, but even then, choosing an oversized rating will stop deflection or metal fatigue during seasonal expansion and contraction. A solid steel tube design, reinforced plates, and precise threads make an adjustable jack post that provides safe support even under constant pressure. Matching the load capacity of Jack Posts to the structure ensures they last, don't settle, and remain structurally sound over the long term during renovation and repair projects.
Adjustment Range and Height Flexibility
The ability to adjust the height of Jack Posts makes them useful across a wide range of structural settings, especially in basements and crawl spaces where ceiling heights can vary widely. Telescoping designs let installers make small changes to the amount of support, allowing them to fix sagging, align beams, and level floors. A typical adjustable range is 3 to 6 feet, but taller models can reach over 10 feet. It gives users the freedom they need for home repairs and temporary shoring.
An adjustable jack post lets you set beams in place with the accuracy you need before starting work on a renovation. When lifting older floors, it's important to make small height adjustments to keep the beam from being overstressed or the finished surfaces from cracking. Homeowners who do their own work like models with screw mechanisms that turn easily, so they can make adjustments without using heavy tools. Shorter posts with wide adjustment threads are best for quickly stabilizing beams in tight crawl spaces where movement is limited. They don't need complicated setup procedures.
For big structural repairs, contractors might use taller Jack Posts and cribbing to reach overhead beams while moving loads safely. A basement floor jack makes it easier to lift heavy items, providing the support workers need to replace rotten beams, install new joists, or level entire sections of the floor. Some models have locking pins that make the adjustment process safer, especially when posts need to stay in place for weeks or months. These features, along with threaded screw caps, allow you to level things perfectly, distribute loads evenly, and keep things strong. Jack Posts will work well in any structural support situation when the appropriate adjustment ranges are selected.
Matching Load & Height Specifications
In the real world, you need to match the load capacity and height range to find the best Jack Posts for the job. A post that can support heavy structural loads must also be long enough to reach the beams without over-threading or destabilizing the structure. The main floors may need taller posts with higher compression strength to handle the weight of the home, while crawl spaces usually have shorter posts that can handle lighter loads but need stronger resistance to moisture and soil movement.
A basement jack post is a good choice for reinforcing older homes because it can be adjusted and safely holds a lot of weight. When installed correctly, a post that can hold 18,000 pounds and has a 4–8-foot adjustment range can stabilize entire sections of a room. A basement floor jack and several posts are often used together for temporary repairs to lift things safely and evenly. Long-term installations, on the other hand, require posts with rust-resistant coatings, thicker steel walls, and secure top plates that fit snugly against beams.
An adjustable jack post ensures everything stays level when walls are taken down or beams are replaced. Contractors often use heavy-duty posts to keep things in line during new framing installation. When doing foundation work, choosing a post that can handle both the vertical reach and the load will make it last longer. Correct matching in each case makes sure that Jack Posts provide stable, safe, and code-compliant support for a wide range of structural needs.
Choosing a Jack Post by Project
The right post depends on the clearance and the job, so we suggest matching your project to the setup below.
| Project | Priority Post | Key Consideration | Why It Fits |
| Low crawl space with little headroom | Compact post, 11.6 to 16 in | Clearance | A short closed height fits under the beam, and a galvanized finish listed on the 4-pack helps in damp spaces. |
| Sagging floor in a low basement | Short post, 19 to 36 in at 18000 lbs | Load per unit | High per-unit capacity at low height supports heavy beams without needing tall reach. |
| Full-height basement ceiling | Tall post, 53 to 93 in or 56 to 100 in | Reach | A telescoping range covers a full ceiling height while keeping an 18000 lbs rating. |
| Very tall space above 8 ft | Tall post, 54 to 150 in | Load versus reach | The extra reach comes with a lower 11200 lbs rating, so spread the load across more posts. |
| Replacing or shoring a 4 x 4 wood post | Screw jack post | Post size | Built to fit 4 x 4 wood posts, with a removable lever for storage. |
| Support that stays up for weeks | Post with lock pins | Locking | Lock pins hold the set height, which matters when the post stays in place during longer repairs. |
Material & Installation Overview
The quality of the materials used directly affects how well and how long Jack Posts last. Heavy-gauge steel, anti-corrosion coatings, and reinforced plates help keep moisture out of the basement and protect it from long-term compression. To install it correctly, make sure the base is attached to solid surfaces, center the post under the beam, and make adjustments slowly. Using high-quality materials and following proper installation steps for a basement jack post or a shorter crawl-space support ensures the structure is safe, stable, and long-lasting.
Best-Seller Comparison
At VEVOR, we compare the first five jack posts on this page side by side, because pack size, height range, and load rating decide how each one fits your structure.
| Product | Pack Size | Height Range | Max Load Per Unit | Adjustment | Net Weight | Best For |
| 4-Pack House Floor Jacks, 11.6-16 In | 4 | 11.6 to 16 in | 2500 lbs | Twist nut, turned with a wrench | / | Only 4-pack and the only galvanized unit; many low supports for light leveling |
| 2-Pack House Floor Jacks, 53-93 In | 2 | 53 to 93 in | 18000 lbs | Lever with lock pins | 49.2 lbs | Top rating with tall reach; full-height basement ceilings needing 18000 lbs |
| 2-Pack House Floor Jacks, 54-150 In | 2 | 54 to 150 in | 11200 lbs | Lever with 8 lock pins | 74.7 lbs (33.9 kg) for the 2-pack | Longest reach as a pair; high ceilings where height matters more than rating |
| 2-Pack House Floor Jacks, 19-36 In | 2 | 19 to 36 in | 18000 lbs | Lever with 4 lock pins | 27.8 lbs | Short range with an 18000 lbs rating; crawl spaces and low basements |
| House Floor Jack, 54-150 In, Single | 1 | 54 to 150 in | 11200 lbs | Lever with multiple lock pins | 17.15 kg | Single unit with the tallest reach; one tall support at a time |
Why Choose VEVOR Jack Posts?
VEVOR Jack Posts are made of strong steel, can hold a lot of weight, and can be adjusted to different heights. They are also very affordable. They are good for basements, crawl spaces, and structural repairs, and they provide reliable support when you need it. Users can choose from a range of sizes to find the one that fits their needs. These supports are strong and built to last, helping keep the structure safe during repairs and renovations. Explore VEVOR Jack Posts today to find reliable structural support solutions designed for safety, strength, and dependable home improvement performance.
FAQs
How do I choose the right shoring post or jack for my project?
Match the per-unit load rating to the weight carried, then check that the post reaches the beam within its height range. Compare adjustment and lock pins too, as on the 2-pack 53 to 93 inch jacks.
Are there safety guidelines for installing shoring posts and jacks?
Set the base on a solid surface, center the post under the beam, and turn the lever or nut slowly. Keep posts aligned, since off-center loading can buckle a post below its rating. Follow the manual and local code.
What are the different types of building jacks and their uses?
Compact posts suit low crawl spaces, short 19 to 36 inch posts suit low basements, and tall telescoping posts suit full ceilings. A screw jack post fits 4 x 4 wood supports. Browse the Jack Posts range.
What safety precautions should I take when installing temporary support posts?
Never exceed the rated load, use every lock pin supplied, and raise the beam in small steps. Keep the post plumb, protect finished floors, and treat it as temporary support. Ask a professional about load-bearing beams.
How do I choose the right adjustable jack for home projects?
Choose by clearance first, then load. Lever models adjust without extra tools, which suits DIY work, and compact posts fit low spaces. See the 4-pack 11.6 to 16 inch jacks for light leveling.
How do I choose the right floor jack with stand for my workshop?
This page covers house floor jacks, which are adjustable support posts, not wheeled hydraulic jacks. For a workshop, pick a post by load rating, height range, and locking pins to match the structure you are supporting.
how to install jack post
Place the base on a solid surface, center the post under the beam, and raise it slowly with the lever or nut. Insert the lock pins, check the post is plumb, and follow the manual and local code.
How do I choose the right jack post for my home renovation?
Estimate the load, measure from floor to beam, and pick a post whose range and rating exceed both. Use several posts for wide spans. For low basements, consider the 2-pack 19 to 36 inch jacks.